  |
|
| Home | Request Information | About MAX-PAK | Equipment | Contacts | |
|
 |
Designed
and built by people with 25 years of experience in baling and
transporting materials for recycling. Back to Equipment Page |
| STANDARD FEATURES • Key Start - Push Button - Control Station mounted on 15' Sealite • Right or left side mounted power unit • Power unit weather cover • NEMA 4 weather proof gasket control panel • UL listed control panel • Override - packout - hydraulic pressure boost OPTIONS • Additional keyed start/stop remote push button station on 15' Sealite • 75% full advanced warning light • 575 volt motor • Multi-cycle timer • Low oil / high temp light • 3-sided hopper (left or right feed) • 4-sided top hopper • 5' guide island • Walk / drive-on dock mounts with 42" hopper & island rails • Walk / drive-on dock mounts with safety gate hopper & hand rails |
SPECIFICATIONS
| MP200HD | MP300HD | MP400HD | MP500HD | |
|
Charge Box Capacity |
2yd | 3yd | 4yd | 5yd |
|
Clear Top Opening |
40.5x60 | 50x60 | 65x60 | 85x60 |
|
Cycle Time |
57 sec | 60 sec | 60 sec | 80 sec |
|
Total Force Normal |
47,600 | 47,600 | 64,600 | 64,600 |
|
Total Force Maximum |
56,000 | 56,000 | 76,000 | 76,000 |
|
Total Face Pressure Normal |
27 psi | 27 psi | 36 psi | 36 psi |
|
Ram Face Pressure Maximum |
31 psi | 31 psi | 43 psi | 43 psi |
|
Ram Penetration |
14" | 14" | 14" | 14" |
|
Motor |
10hp | 15hp | 15hp | 20hp |
|
Cylinder Bore |
6" | 6" | 7" | 7" |
|
Cylinder Stroke |
55" | 65" | 80" | 100" |
|
Cylinder Rod |
2.5 | 3.5 | 4.5 | 4.5 |
|
Operating Pressure Normal |
1700 psi | 1700 psi | 1700 psi | 1700 psi |
|
Operating Pressure Maximum |
2000 psi | 2000 psi | 2000 psi | 2000 psi |
|
Unit Weight |
4100 lbs | 5800 lbs | 7500 lbs | 12,000 lbs |
|
Construction: Floor |
1/2" Plate | 1/2" Plate | 1/2" Plate | 3/4" Plate |
|
Sides |
1/4" Plate | 1/4" Plate | 1/4" Plate | 3/8" Plate |
|
Breaker Bar |
8x6x1 Angle | 8x6x1 Angle | 8x6x1 Angle | 8x6x1.5 Angle |
|
Ram Face |
1/2" Plate | 1/2" Plate | 3/4" PLate | 3/4" Plate |
|
Ram Top |
1/4" Plate | 1/4" Plate | 1/4" Plate | 3/8" Plate |
|
Ram Sides |
1/4" Plate | 1/4" Plate | 1/4" Plate | 3/8" Plate |
|
Ram Bottom |
1/2" AR Plate | 1/2" AR Plate | 1/2" AR Plate | 1/2" AR Plate |
MEASUREMENTS
| Model | A | B | C | D | E |
| MP200HD | 55 | 52 | 117 | 69 | 78 |
| MP300HD | 55 | 61.5 | 136 | 69 | 78 |
| MP400HD | 55 | 76.5 | 179 | 69 | 78 |
| MP500HD | 55 | 96.5 | 220 | 69 | 78 |
| • In order to provide the
most currently engineered and designed equipment, we reserve the right
to change specifications without notice. • Performance may vary application. • Products must be installed and operated according to required standards, codes, regulations and safety procedures. • All MAX-PAK Equipment is provided with A-36 structural steel frames. A-514 reinforced in areas of high stress. Strong rigid container walls provide performance and long service life. A-1018 is used for gib bar, guide and control surfaces. • All MAX-PAK Equipment meets or exceeds all ANSI Z245.5 and OSHA standards. • All MAX-PAK Equipment has NEMA 12 and UL approved electrical panel and control assembly. • MAX-PAK offers several lines of equipment for your recycling needs: Vertical Balers, Horizontal Closed End Balers, Horizontal Open End Balers, Full-Eject Balers, Compactors, Containers, Conveyors and Trailers. |
|
| Home | Request Information | About MAX-PAK | Equipment | Contacts | |
|
© 2001 MAX-PAK Waste Processing Equipment, Inc. All rights reserved. |